Quick Programing Guide
Factory Reset
This command returns your mosfet to the factory default "burst to auto" settings.
1 - set your AEG to semi automatic
2 - plug in your battery
3 - pull the trigger 15 times
4 - mosfet will blink 3 times to confirm the command
5 - wait for solid red light before firing
Battery Synchronization
This function can be used to activate the mosfets low voltage warning and cut-off settings. When these features are activated the mosfet will beep when the voltage of your battery is low and will cease firing if the voltage falls to critically low levels. This function will also use the inputted information to auto configure the unit for optimal use with your battery. No adjustment is needed for NiMH batteries.
Lipo Battery Settings
1 - set your AEG to semi automatic
2 - plug in battery
3 - pull the trigger 4 times
4 - mosfet will blink 4 times
5 - pull the trigger 1 time
6 - mosfet will blink 1 time
7 - mosfet will blink 3 times
8 - wait for solid red light before firing
LiFE Battery Settings
1 - set your AEG to semi automatic
2 - plug in battery
3 - pull the trigger 4 times
4 - mosfet will blink 4 times
5 - pull the trigger 2 times
6 - mosfet will blink 2 times
7 - mosfet will blink 3 times
8 - wait for solid red light before firing
Switching to Full Auto
This command can be used to set your fire select settings to safe, semi, and full auto.
1 - set your AEG to semi automatic
2 - plug in battery
3 - pull and hold the trigger for 2 seconds, then release
4 - mosfet will blink 1 time
5 - wait for solid red light before firing
Switching to (x) Round Burst
This function can be used to set your fire select settings to safe, semi, and three round burst. Please note, the (x) is the number of rounds you would like the AEG to burst. Burst can be from (1-9).
1 - set your AEG to semi automatic
2 - plug in battery
3 - pull the trigger 2 times
4 - mosfet will blink 2 times
5 - pull the trigger (x) times
6 - mosfet will blink (x) times
7 - wait for solid red light before firing
Rate of Fire Adjustment
This command can be used to adjust the rate of fire of your rifle. Each trigger pull in this command will reduce your ROF by 2-3 rounds a second. This reduction will marginally increase the FPS of your AEG. The reduction will also allow for a more consistent FPS and will widen the variety of magazines your rifle will be compatible with. Please note, the (x) is the number of rounds you would like to reduce your ROF by.
1 - set your AEG to semi automatic
2 - plug in battery
3 - pull the trigger 5 times
4 - mosfet will blink 5 times
5 - pull the trigger (x) times
6 - mosfet will blink (x) times
7 - mosfet will blink 3 times
8 - wait for solid red light before firing
Spring Tension Adjustment
This function can be used to adjust the reset point of the AEG's main spring. This will allow you to maximize or minimize the FPS of your rifle. By maximizing your reset point your rifle will be able to take advantage of its maximum compression, thus increasing your FPS and its consistency. My minimizing the reset point your rifles cyclic rate will slightly increase, allowing for a higher ROF. A good median should be found to maximize the effectiveness of your AEG. The range of adjustment of this command is 1-13 trigger pulls. One being the lowest spring tension and thirteen being the highest. This function will require trial and error to obtain an ideal result. Please note, the (x) is level of adjustment. Remember, to reset your unit use command function A. We recommend tuning this setting before any other.
1 - set your AEG to semi automatic
2 - plug in battery
3 - pull the trigger 7 times
4 - mosfet will blink 7 times
5 - mosfet will blink 1 time
6 - pull the trigger (x) times
7 - mosfet will blink (x) times
8 - mosfet will blink 3 times
9 - wait for solid red light before firing
Burst to Auto Delay Adjustment
This command be used to increase the delay between burst and full auto fire when the mosfet is set at the factory settings. By doing this you will have a cleaner three round burst feature while keeping automatic fire available. Please note, the (x) is the number of .1 second delays you would like to add.
1 - set your AEG to semi automatic
2 - plug in battery
3 - pull the trigger 3 times
4 - mosfet will blink 3 times
5 - pull the trigger (x) times
6 - mosfet will blink (x) times
7 - mosfet will blink 3 times
8 - wait for solid red light before firing
Tips and Tricks
- Make sure to wait four seconds after plugging in your battery before firing your AEG.
- After the three quick blinks at the end of a command and before the red light activates (approx. 4 seconds) you can pull the trigger to activate another command.
- Always unplug the mosfet from the power source during storage or prolonged inactivity.
- If you run your battery low enough for the unit to activate its auto shut down and are experiencing issues after installing your fresh battery run the factory reset command.